792 items

Paints & Spray Paints

Paints & Spray Paints
View as List Grid

792 items

Set Ascending Direction Set Descending Direction
  1. Ronseal Chalky Furniture Paint Range




    Inc VAT:  


    Ronseal Chalky Furniture Paint gives a chalk effect with high performance. It protects against wear and tear and will not rub off on touch. No over coating required.

    The paint provides a flat matt, chalky finish.


    Learn More
  2. Ronseal Anti Condensation Paint White Matt Range




    Inc VAT:  


    The Ronseal Anti Condensation Paint adds a layer of insulation to help prevent condensation which leads to mould. Once its dry thats it, job done. Unless you want to add some colour. Then you can paint over it any colour your want. Itll still give the same anti-condensation protection.


    Make sure the room is above 10c. Open your doors and windows for ventilation and put down dust sheets to protect anything you dont want to get paint on.

    Preparation: Remove any wallpaper and get rid of any loose paint or plaster by giving it a quick sand. Make sure the area youre painting is clean and dry. If youve got mould, get rid of it with our 3in1 Mould Killer. Cover any damp stains with our One Coat Damp Seal.


    Give it a really good stir. Then use a roller or brush to put it on. Dont brush or roller it out too thinly. After 4 hours put another generous coat on. Itll be touch dry in 1-2 hours. If you want to paint over it, let it dry for 4 hours.

    Usage Areas: All indoor walls and ceilings.
    Compatibility: Bare and previously painted walls and ceilings.
    Clean Up: Clean all brushes in warm, soapy water.
    Coverage: 6m per Litre.


    Learn More
  3. Ronseal 3 In 1 Mould Killer Range




    Inc VAT:  


    The Ronseal 3 In 1 Mould Killer kills mould instantly, cleans and protects against mould. It breaks down mould and removes it from paint work.

    How to Use.

    Squeeze the trigger to break the tamper evident seal. Repeatedly squeeze the trigger, applying direct to the surface ensuring it is wetted thoroughly (wear suitable gloves).

    Leave for 5 minutes then wipe the surface using a damp cloth or sponge removing the mould. Once the mould has been removed, wipe away any residual grime with a clean damp cloth.

    Clean Up Rinse cloths or sponges in warm, soapy water.

    Usage Areas: For use in areas where mould is present.
    Compatibility: Suitable for use on, bare or previously painted walls and ceilings.
    Clean Up: Clean cloths and sponges in warm soapy water.

    Available in a bottle (concentrate) or spray.


    Learn More
  4. Ronseal One Coat Damp Seal Range




    Inc VAT:  


    The Ronseal One Coat Damp Seal permanently blocks damp stains on walls and ceilings. You can even put it onto damp walls. It lets trapped moisture escape without causing anymore damage. When its dry you can paint or wallpaper over it.


    Make sure the cause of damp has been fixed. Open your doors and windows for ventilation and put down dustsheets to protect anything you dont want to get paint on.

    Preparation: Remove any wallpaper with a scraper and sand off any loose or flaking paint. Make sure the area you are painting is clean, if youve got mould, get rid of it with our 3-in-1 Mould Killer.

    You can paint onto damp surfaces, just make sure theyre not dripping wet.


    Give the paint a really good stir, then use a roller or brush to put it on. If youre covering a small damp patch, make sure you are painting at least 30cm around the area.

    Itll be touch dry in 2 hours. After 4 hours itll be ready to paint or wallpaper over. If the area is prone to mould, you can paint over it with our 6 Year Anti-Mould Paint.

    Usage Areas: All indoor walls and ceilings
    Compatibility: Bare or previously painted walls and ceilings
    Clean Up: Clean all brushes or rollers in warm, soapy water
    Coverage: 5m per litre


    Learn More
  5. Rustins Chalky Finish Paint Range




    Inc VAT:  


    The Rustins Quick Dry Chalky Finish Paint is designed to revive and give your furniture a new lease of life. Suitable for use on interior work, it contains wax and dries to a velvety flat matt finish.

    Very little preparation is required to receive the desired look as it can be painted over most previously coated items. If using over a previously coated surface, test a small area for compatibility. Use on bare wood, hardboard, MDF, plaster, brickwork and cement to produce a smooth touch flat matt finish. (Not for direct application to metals). Can also be used as a finish coat over existing wood and metal primers and paints.

    Get the shabby chic look by painting your furniture with multiple coats then distressing it by lightly sanding down small areas using fine sandpaper or steel wool.


    Coverage Approximately: 13m per litre
    Coats: 1 coat over primed surfaces, 2 coats (minimum) are required on bare substrates
    Drying Time: Touch Dry 30 minutes, depending on temperature and humidity
    Re-coating Time: 2 hours minimum, depending on temperature and humidity
    Application Temp: Ideally 15-25C. Do not use below 10C or in conditions of high humidity


    Learn More
  6. Ronseal Stain Guard Clear Coat Matt Range




    Inc VAT:  


    Ronseal One Coat Stain Guard is a clear coat the protects paint from stains. It is ideal for areas that are always getting dirty, marked or stained. It provides a tough, scrubbable finish and does not discolour.

    Usage: All interior walls and ceilings.
    Compatibility: Previously painted walls and ceilings.
    Coverage: 24m per litre.


    Learn More
  7. Rustins Masonry Paint Range




    Inc VAT:  


    Rustins Quick Dry Masonry Paint is a high quality, acrylic paint which is suitable for dry exterior masonry surfaces.

    To apply, use a large brush and apply evenly. The surface area must be clean, dry, free from dust and other contaminants likely to affect adhesion. No primer is required if fresh mortar has been applied to pointing. Do not use on damp surfaces.

    One coat is usually sufficient.

    Drying time: approx 30 mins, depending on temperature and humidity.
    Re-coat: 4 hours.
    Coverage: 14m per 1 litre.


    Learn More
  8. Rustins Quick Dry All Surface All Purpose (ASAP) Paint Range




    Inc VAT:  


    Rustins Quick-Drying All Surface All Purpose (ASAP) Paint is a water based paint that dries to a satin finish. It resists flaking or peeling because of its flexible capabilities.

    ASAP has a low odour and does not require any priming. It is suitable for use on wood, metal, plastic, galvanised steel, uPVC, lead, glass, tiles, plaster, mdf, masonry and melamine.


    Learn More
  9. Plasti-kote 1809 Stained Glass Spray 200ml Range




    Inc VAT:  


    PlastiKote Stained Glass Spray is ideal for use on clear glass and plastic and is available in a wide range of colours. It comes in a handy 200ml spray and is ideal for small project or craft uses.

    Use only in well ventilated areas. Ensure surface is clean and dry. Shake can well before and during application. Several thin coats are recommended rather than one heavy coat. Before applying spray on an inconspicuous area to ensure compatibility and suitability

    Available in 7 superb colours. Please note that the cap is not a true representation of the colour and finish.

    Coverage: Approximately 1.2 m.
    Touch Dry: 45 Minutes.
    Thoroughly Dry: 3 Hours.


    Learn More
  10. Zinsser Allcoat Exterior Primer Range




    Inc VAT:  


    Zinsser ALLCOAT Exterior Primer / Finish is the best performance all surface paint. Designed for the long term decoration of timber, metal, masonry, plastic, concrete, cladding and more, it forms a Vapour permeable, low maintenance water-shedding coating, re-coatable in 1 hour.

    ALLCOAT Exterior contains a biocide to protect the dried coating against fungal degradation. Designed for all exterior surfaces, ALLCOAT Exterior is ideal for new or previously painted wood, UPVC, galvanising, metals, cladding, weathered bitumen, stucco, brick, stone, cured concrete and more.

    ALLCOAT Exterior is self-priming and will bond to existing glossy paints without sanding. For most jobs, there is no need to purchase a separate primer. After removing existing mould and mildew, two coats of ALLCOAT Exterior will ensure that any exterior looks bright and beautiful for years.

    Zinsser ALLCOAT Exterior gives excellent resistance against:

    Cracking, blistering and flaking.
    Rain and severe weather.

    Long lasting finish.
    Easy to apply.
    Excellent colour retention.
    Multi-surface application.

    Surfaces should be clean, dry, sound and free of any contamination that may interfere with adhesion. Remove all loose or peeling paint and chalky paint residue. Sand edges of any remaining paint film until smooth. Special precautions should be taken during surface preparation of pre- 1960 paint surfaces as they may contain harmful lead.

    Avoid the inhalation of dust. Wear a suitable face mask if dry sanding. New concrete, masonry and other related surfaces must be cured at least 30 days before priming. Remove all existing mould and mildew before painting.


    Learn More
No more product
Paints & Spray Paints
© 2020 Building Supplies Direct Online Ltd
VAT Number: 100 5143 84