Smoke Testers & Tracing Dyes

The Baileys Drain Tracing Dyes are soluble in water and are used to locate the direction of water flow in pipes, drains etc.

The best way to use the dye is to dissolve the required amount into about five litres of water and then add into the flow or tank. The dilution rates assume that the dye is being added to clean water, for examle one 8oz jar will provide enough dye for approximately 15,000 litres/3,300 gallons of water.

However please note that dirty water will require a greater concentration of dye.

The Baileys BAI3591 Drain Tracing Dyes is 8 ounces (200 grammes)
Colour: Yellow
Part No: 3591
Dilution Rates Litres: 10-12,000

PTDBAI3591

The Baileys Drain Tracing Dyes are soluble in water and are used to locate the direction of water flow in pipes, drains etc.

The best way to use the dye is to dissolve the required amount into about five litres of water and then add into the flow or tank. The dilution rates assume that the dye is being added to clean water, for examle one 8oz jar will provide enough dye for approximately 15,000 litres/3,300 gallons of water.

However please note that dirty water will require a greater concentration of dye.

The Baileys BAI3592 Drain Tracing Dyes is 8 ounces (200 grammes)
Colour: Purple
Part No: 3592
Dilution Rates Litres: 12-14,000

PTDBAI3592

The Baileys Drain Tracing Dyes are soluble in water and are used to locate the direction of water flow in pipes, drains etc.

The best way to use the dye is to dissolve the required amount into about five litres of water and then add into the flow or tank. The dilution rates assume that the dye is being added to clean water, for examle one 8oz jar will provide enough dye for approximately 15,000 litres/3,300 gallons of water.

However please note that dirty water will require a greater concentration of dye.

The Baileys BAI1992 Drain Tracing Dyes is 8 ounces (200 grammes)
Colour: Blue
Part No: 1992
Dilution Rates Litres: 12-14,000

PTDBAI1992

The Baileys Drain Tracing Dyes are soluble in water and are used to locate the direction of water flow in pipes, drains etc.

The best way to use the dye is to dissolve the required amount into about five litres of water and then add into the flow or tank. The dilution rates assume that the dye is being added to clean water, for examle one 8oz jar will provide enough dye for approximately 15,000 litres/3,300 gallons of water.

However please note that dirty water will require a greater concentration of dye.

The Baileys BAI3589 Drain Tracing Dyes is 8 ounces (200 grammes)
Colour: Green
Part No: 3589
Dilution Rates Litres: 15-20,000

PTDBAI3589

The Baileys Drain Tracing Dyes are soluble in water and are used to locate the direction of water flow in pipes, drains etc.

The best way to use the dye is to dissolve the required amount into about five litres of water and then add into the flow or tank. The dilution rates assume that the dye is being added to clean water, for examle one 8oz jar will provide enough dye for approximately 15,000 litres/3,300 gallons of water.

However please note that dirty water will require a greater concentration of dye.

The Baileys BAI3590 Drain Tracing Dyes is 8 ounces (200 grammes)
Colour: Red
Part No: 3590
Dilution Rates Litres: 12-15,000

PTDBAI3590

Monument smoke emitter pellets give off a dense white low-toxic smoke when ignited. They have a burn time of 60 seconds.

For testing flues, chimneys, fans etc.

Supplied in a pack of 10.

PTDMON1470

The Arctic Hayes Smoke-Sticks Kit is the first product on the market offering a pencil thin smoke pattern. The smoke is non-corrosive and not harmful. Ideal for testing for the slightest air-movement, gas spillage. Also for mandatory CO spillage checks of boiler/case sills after fitting/re-fitting and HVAC air-movement/leakage checks.

The Smoke-Sticks Kit comes with 3 Smoke-Sticks providing up to 3 hours of controllable smoke. Refill pack also available.

1 x Arctic Hayes Smoke-Sticks Refill Pack of 3

PTDARC333103

The Arctic Hayes Smoke-Sticks Kit is the first product on the market offering a pencil thin smoke pattern. The smoke is non-corrosive and not harmful. Ideal for testing for the slightest air-movement, gas spillage. Also for mandatory CO spillage checks of boiler/case sills after fitting/re-fitting and HVAC air-movement/leakage checks.

The Smoke-Sticks Kit comes with 3 Smoke-Sticks providing up to 3 hours of controllable smoke. Refill pack also available.

The Arctic Hayes Smoke-Sticks Kit comes with:

1 x Smoke-Pen
3 x Smoke-Sticks

PTDARC333113

The Arctic Hayes Standard 13g Smoke Pellets offer a 40 second burn time and produces 18m of smoke.

Supplied in a tube of 6 pellets.

PTDARCPH001

Arctic Hayes Strikes Smoke Matches are ideal for spillage testing on gas appliances or initial flue draw testing. Clean to use with no residue and cool to the touch after burning. They have a 20 second burn time and each match produces about 0.75m of dense smoke.

Great value pack of 25 comes in a protective resealable tub.

PTDARC333000