Gas Pipe & Drain Installation

Monument Tee Piece for U Gauge connects three pieces of rubber hose together for convenient connection to U Gauge, bellows and nipple cap.

PTDMON183

The Monument MON180 180S nipple cap for attachment to drain test plug outlets to enable connection of rubber hose to the U Gauge.

Size: 1/2 inch BSP.

PTDMON180

Using Monument Hand Bellows, air may be carefully pumped into the pipe.

Fitted with a positive, hand operated non-return valve.

Designed for use with Monument Air testing U Gauge kit.

PTDMON179

The Monument Air Bag Stopper is a durable, quality flexible air bag stopper for the plugging of drains and pipes. This bag is made with a durable nylon outer casing that gives the air bag a better seal and grip on the tube or pipe being repaired or replaced. It has a long feed hose that is fitted with a Schrader valve to quickly release the pressure.

Inflate with a MON1308 pump.

PTDMON1292

Monument Pipe Dry Testing Kit is ideal for dry testing pipework during and after installation. The 1512 has an easy to read triple scale bar in psi and kPa scales and is suitable for water, air, gas and petroleum oil pipes up to 4 bar, and for testing combi systems.

Can be left on test, while flooring is laid to reveal any nail damage. It can also test hot and cold supplies separately to ensure pipes are not crossed. The Monument 1512 is fitted with a Schrader Valve and 15 mm push-fit fitting for quick and easy assembly and has a rubber boot for added protection.

PTDMON1512

Inflatable rubber bladder with canvas protective case which can be used for blocking off pipes during maintenance and similar applications.
Supplied with 1/4 in brass tap and 1.8 metres (6 ft) of tubing.

PTDGRPBAI1968

Monument Drain Testing Plugs are durable, quality flexible drain plug for the plugging of drains and pipes. This plug is easy to use and are available in various sizes. Fitted with removable top caps and rubber rings.

These plugs are easy to use just place in the pipe end that is being repaired or replaced and simply turn the wing nut knob, this will depress the rubber cone, this will make it expand to seal pipe or tube end with a water tight seal.

The Monument MON1377 1377W Drain Testing Plug comes with the following specifications:
Size: 75mm (3 inch).
Capable of sealing against pressures of up to 2.24 bar / 33 psi.

PTDMON1377

Monument Drain Testing Plugs are durable, quality flexible drain plug for the plugging of drains and pipes. This plug is easy to use and are available in various sizes. Fitted with removable top caps and rubber rings.

These plugs are easy to use just place in the pipe end that is being repaired or replaced and simply turn the wing nut knob, this will depress the rubber cone, this will make it expand to seal pipe or tube end with a water tight seal.

Monument 1378Z Drain Testing Plug.

Size: 100 mm (4 in).
Capable of sealing against pressures of up to 1.97 bar / 29 psi.

PTDMON1378

Centre locking drain test plugs with steel plates, brass wing nuts and plastic blanking caps. Suitable for air or water testing of drains and sewers.

PTDGRPBAI1963

Centre locking drain test plugs with steel plates, steel wing nuts and brass blanking caps. Suitable for air or water testing of drains and sewers.

PTDGRPBAI2416

Monument Gas Test Gauge is made from tough plastic. Used both for testing pipework installations with air for leaks before the introduction of gas and for checking and setting correct gas pressures on domestic and commercial appliances.

Extruded cover slides off and may be clipped over the base for standing the tool vertically during use.

Hanging tab permits vertical hanging from suitable protrusions. Marked in millibars, the scale adjusts for zeroing water level.

Plastic U Tube.

Monument 257C Gas Test Gauge.

Size: 300mm (12 in).
Capacity: 30 Millibar.

PTDMON257

Monument Gas Test Gauge is made from tough plastic. Used both for testing pipework installations with air for leaks before the introduction of gas and for checking and setting correct gas pressures on domestic and commercial appliances.

Extruded cover slides off and may be clipped over the base for standing the tool vertically during use.

Hanging tab permits vertical hanging from suitable protrusions. Marked in millibars, the scale adjusts for zeroing water level.

Plastic U Tube.

Monument 258F Gas Test Gauge.

Size: 600mm (24 in).
Capacity: 60 Millibar.

PTDMON258

Monument Gas Test Gauge is made from tough plastic. Used both for testing pipework installations with air for leaks before the introduction of gas and for checking and setting correct gas pressures on domestic and commercial appliances.

Extruded cover slides off and may be clipped over the base for standing the tool vertically during use.

Hanging tab permits vertical hanging from suitable protrusions. Marked in millibars, the scale adjusts for zeroing water level.

Plastic U Tube.

Monument 259I Gas Test Gauge has the following specification:

Size: 900mm (36in).
Capacity: 90 Millibar.

PTDMON259

The Monument MON1277S Replacement Hose to fit Gas Test Gauges.

Length: 1 metre (Coil).

Note: Do not use this hose for LPG (low pressure gas).

PTDMON1277S

The Monument MON1445 1445F spare hose for connecting testing equipment comes in the following:

Length: 1 metre (3/8 inch).

PTDMON1445